Sykesville, MD

perform a routine inspection of their leak detection system. After checking in with the facility manager, I reviewed the sensors, piping, and monitoring equipment for any signs of malfunction or leaks. During the inspection, I found that one of the sensors in the coolant storage area was not responding, likely due to a buildup of debris around the sensor. To resolve the issue, I cleaned the sensor and tested it to ensure it was functioning correctly. After confirming the system was operating properly, I updated the maintenance records and informed the facility manager of the repair, recommending regular cleaning of the sensors to maintain optimal performance.

I replaced the hot shutoff valve underneath the kitchen sink and switched out the filter on the whole house system.

I was called to replace an ice maker valve behind a refrigerator. The valve was leaking, and the customer wanted to avoid the inconvenience of a flooded kitchen. I removed the old valve and installed a new one, ensuring a tight seal. The customer was grateful for the quick and efficient service.

I repaired a leaking water heater for a homeowner in Sykesville. Upon inspection, I discovered that the temperature and pressure relief valve was malfunctioning and causing the leak. I drained the water heater and replaced the faulty valve with a new one. After refilling the tank, I checked the anode rod for corrosion and found it in good condition. I also tested the thermostat and heating elements to ensure the water heater was functioning correctly. After confirming everything was working, I cleaned up the work area. The homeowner was happy to have the leak fixed, and the unit is now running smoothly.

I was called to repair a leaking toilet in Sykesville that had a worn-out wax ring. After removing the toilet from the base, I replaced the old wax ring with a new one and reset the toilet. I also tightened the mounting bolts and checked the water supply line for any leaks. After reassembling the system, I tested the toilet to ensure everything was functioning correctly. The repair was successful, and the toilet is no longer leaking.

I performed a slab leak detection for a client in Sykesville. The area of concern was in the kitchen; I used an electronic leak detection device. After pinpointing the leak, I exposed the area and found a cracked copper pipe. I replaced the damaged section of the pipe with new copper tubing, then tested the system for any additional leaks. Everything is now secure, and the water lines are functioning correctly. The customer was relieved to have the issue resolved quickly.

I was called to repair a water line that had developed a leak under the home's slab. After performing electronic leak detection, I located the source of the leak in the copper water line. I shut off the water supply and carefully exposed the affected section. I cut out the damaged pipe and replaced it with a new piece of copper tubing, securing it with press fittings. Once the repair was completed, I turned the water back on and tested the system for leaks. The repair was successful, and the water line is functioning properly again. The homeowner was relieved the issue was resolved.

Today, I provided an estimate for a bathroom remodel. The project includes replacing the shower, vanity, and toilet, along with installing new fixtures and updating the plumbing. I assessed the current layout and discussed the customer’s preferences for materials and design. The estimate covers labor, materials, and any necessary adjustments to the existing plumbing. I also explained the timeline for completion and potential costs for unforeseen issues. The customer now has a detailed estimate and is considering moving forward with the project.

I repaired a 50-gallon water heater that was not producing hot water consistently. After inspecting the unit, I found that the thermostat and heating element were faulty. I drained the water heater to access and replace both components. The old heating element showed signs of corrosion, which was contributing to the issue. I installed a new thermostat and heating element, then refilled the tank and tested the system. The water heater is now functioning properly, with consistent hot water being delivered. I confirmed everything was working efficiently before completing the job and leaving the site.

I installed a new American Standard 40-gallon gas water heater for a customer. The old unit was beyond repair due to sediment buildup. After installing the new tank, I connected the gas line, ran new flexible water connections, and tested the unit. Hot water is now restored, and the system is working perfectly.

A low water pressure issue was reported in the kitchen faucet. I disassembled the faucet and found the aerator clogged with mineral deposits. After thoroughly cleaning the aerator, I flushed the supply lines to clear any additional buildup. I also made minor adjustments to the pressure reducing valve (PRV) to optimize water flow. After completing these steps, the water pressure in the kitchen faucet was restored to normal levels, and the sink is now functioning efficiently with proper flow.

Today, I installed a battery backup sump pump along with a new primary pump in the customer's basement. The backup system ensures that the sump pump will continue to operate during power outages, providing extra protection against flooding. I securely installed both pumps, connected the discharge lines, and tested the system to ensure everything was functioning properly. The battery backup activated as expected, and the primary pump is working efficiently. The installation was completed successfully, and the system is now set up to provide reliable flood protection.

I repaired an AO Smith gas water heater that was experiencing intermittent hot water issues. The problem was traced to a malfunctioning gas control valve. I replaced the valve with a new OEM part, ensuring compatibility and safe operation. After completing the repair, I tested the water heater, confirming consistent hot water delivery and proper burner operation.

I unclogged a bathroom sink drain using a Milwaukee M12 drain snake. The blockage was caused by hair and soap buildup in the P-trap. After removing the clog, I cleaned the drain and reassembled the P-trap, ensuring everything was tightly sealed. I tested the sink, and it now drains efficiently with no signs of further obstruction.

I detected a slow leak in a PEX water line using an ultrasonic leak detector. The homeowner had noticed a musty odor and dampness in their basement. After locating the source of the leak, I shut off the water supply, cut out the damaged section of the PEX tubing, and installed a new piece with SharkBite fittings. The repair was tested, and no further leaks were detected.

I replaced an old electric water heater with a new Rheem Performance Plus 50-gallon unit. The installation required updating the electrical wiring to accommodate the new heater's requirements and replacing the water supply lines with FlexiBraided connectors. After securely mounting the heater, I filled the tank, checked for leaks, and tested the unit to ensure proper heating. The new system is running efficiently, providing consistent hot water.

I was called to a home in the suburbs to replace a sump pump and check valve. The sump pump was located in the basement and was not working properly. I removed the old pump and check valve and installed a new one. I also checked the electrical connections and made sure everything was working properly. The homeowner was very pleased with the work and thanked me for my help.

I was called to a home to unclog a kitchen sink drain. I used a k-50 to snake out the drain. I was able to remove the clog and the customer was happy with the service.

I am a highly skilled and experienced home service professional. I recently completed a job that involved installing a whole house filter, changing out a leaking gauge on a well pressure tank, and replacing a frost-proof hose bib with a new one. The job required careful attention to detail and the ability to work efficiently to ensure that the job was completed on time and to the customer's satisfaction.

Unclogged and repaired a Kohler Cimarron toilet. Utilized a RIDGID K-6 toilet auger to clear the blockage, ensuring proper water flow. Inspected the flapper and fill valve, replacing them with Fluidmaster 400A and Korky 54BP parts respectively, to ensure efficient operation and water conservation. Tested the flush mechanism to confirm all components were working correctly. Regular maintenance and prompt repairs keep your plumbing fixtures in optimal condition. For expert toilet repair services, contact us for reliable solutions.

Performed a kitchen drain clean-out using a RIDGID K-50 sectional machine with a 5/16" x 35' cable to effectively clear blockages. Removed grease, food particles, and other debris causing the clog. Inspected the P-trap and drain lines to ensure there were no additional obstructions or damage. Tested the drain for proper flow to confirm the blockage was completely cleared. Regular drain maintenance prevents clogs and ensures efficient plumbing. For professional drain cleaning services, contact us to keep your system running smoothly.

Performed a thorough drain cleaning to address a clogged kitchen sink. Used a RIDGID K-400 drum machine with a 3/8" x 75' cable to clear the blockage effectively. Inspected the P-trap and drain lines for any damage or buildup, ensuring smooth water flow. Regular drain cleaning prevents blockages and maintains plumbing efficiency. For professional drain cleaning services, contact us to keep your plumbing system running smoothly and prevent future issues.

Repaired a 40-gallon Bradford White water heater. Diagnosed a faulty thermostat and heating element, both of which were causing inconsistent water temperatures. Replaced the thermostat with a Bradford White OEM part and installed a new heating element to restore efficient operation. Flushed the tank to remove sediment buildup, ensuring optimal performance and longevity. Regular maintenance and timely repairs are crucial for reliable hot water supply. For expert water heater repair services, contact us to keep your system running smoothly.

I was called to replace an existing Delta kitchen faucet with a homeowner supplied Moen kitchen faucet. The homeowner had chosen the Moen faucet and provided the necessary parts. I removed the old faucet and installed the new Moen faucet, ensuring a tight seal. I also replaced the supply lines and connected the faucet to the water supply. I tested the faucet to ensure it was working properly and made any necessary adjustments. The homeowner was pleased with the results and thanked me for my work.

I was called to a home to diagnose a leak in a bathtub. Upon inspection, I found that the faceplate trim was defective, allowing water to seep into the wall and then downstairs. I replaced the Delta faceplate trim and handle kit to fix the issue.